4 Channel Waterproof DMX512 & RDM Decoder 12V 24V 36V D4-WP

Product Name: DMX 512 Decoder / RDM Decoder

Model: MJJC-D4-WP

IP67 waterproof/RDM/Stand-alone function/Two PWM frequency/Linear or logarithmic dimming/Numeric display

Features:

● Waterproof DMX512 decoder with IP67 rating, suitable for outdoor and damp environment.
● Comply with the DMX512/RDM standard protocols.
● Digital numeric display, set DMX decode start address by buttons.
● 1/2/4 DMX channel output selectable.
● PWM frequency 2000/500Hz selectable.
● Logarithmic or linear dimming curve selectable.
● Stand-alone RGB/RGBW mode and 4 channel dimmer mode selectable,
which be controlled by buttons with built-in programs, instead of DMX signal.
● Over-heat / Over-load / Short circuit protection, recover automatically

DMX Mode:

● Short press MODE key, when display 001~999, enter DMX mode.
● Press ◀ or ▶ key to change DMX decode start address(001~999),
long press for fast adjustment.
● If there is a DMX signal input, will enter DMX mode automatically.
● DMX Dimming: Each D4-WP DMX decoder occupy 4 DMX address
when connecting the DMX console.
For example, the defaulted start address is 1,
their corresponding relationship in the form:

Stand-alone RGB/RGBW mode:

● Enter stand-alone RGB/RGBW mode only when DMX signal is disconnected or lost.
● Short press MODE key, when display P01~P30, enter stand–alone RGB/RGBW mode.
● Press ◀ or ▶ key to change dynamic mode number(P01~P30).
● Each mode can adjust speed and brightness.
Short press SETUP key for switch between mode speed,
brightness and W channel brightness setting.
Press ◀ or ▶ key to setup value of each item.
Mode speed: 1-10 level speed(S-1, S-9, S-F).
Mode brightness: 1-10 level brightness(b-1, b-9, b-F).
W channel brightness: 0-255 level brightness(400-4FF).
Long press SETUP key for 2s, or timeout 10s, quit setting

Stand-alone dimmer mode:

Enter stand-alone dimmer mode only when DMX signal is disconnected or lost.
● Short press MODE key, when display L–1~L–8, enter stand–alone dimmer mode.
● Press ◀ or ▶ key to change dimmer mode number(L–1~L–8).
● Each dimmer mode can adjust each channel brightness independently.
Short press SETUP key to switch between 4 channel(100~1FF, 200~2FF, 300~3FF, 400~4FF).
Press ◀ or ▶ key to setup brightness value of each channel.
Long press SETUP key for 2s, or timeout 10s, quit setting.

RGB Change Mode list:

No.	Name	No.	Name	No.	Name
P01	Static red	P11	P21	Green strobe	Red yellow smooth
P02	Static green	P12	P22	Blue strobe	Green cyan smooth
P03	Static blue	P13	P23	White strobe	Blue purple smooth
P04	Static yellow	P14	P24	RGB strobe	Blue white smooth
P05	Static cyan	P15	P25	7 color strobe	RGB+W smooth
P06	Static purple	P16	P26	Red fade in and out	RGBW smooth
P07	Static white	P17	P27	Green fade in and out	RGBY smooth
P08	RGB jump	P18	P28	Blue fade in and out	Yellow cyan purple smooth
P09	7 color jump	P19	P29	White fade in and out	RGB smooth
P10	Red strobe	P20	P30	RGBW fade in and out	6 color smooth

System parameter setting:

● Long press SETUP key for 2s, prepare for setup system parameter:
decode mode, output PWM frequence, output brightness curve, automatic blank screen.
then short press SETUP key to switch four item.
● Decode mode: short press ◀ or ▶ key to switch 1/2/4 channel decode mode(“d-1“,“d-2” or “d-4“). When set as 1 channel
decode, the decoder occupy only 1 DMX address, and four channel output the same brightness of this DMX address.
● Output PWM frequence: short press ◀ or ▶ key to switch 500Hz(“F-L“) or 2KHz(“F-H“).
Higher PWM frequency, will cause lower output current, higher power noise, but more suitable for camera(No flickers for video).
● Output brightness curve: short press ◀ or ▶ key to switch linear curve(“C-L“) or logarithmic curve(“C-E“).
● Automatic blank screen: short press ◀ or ▶ key to switch enable (“bon“) or disable(“boF“) automatic blank screen.
● Long press SETUP key for 2s or timeout 10s, quit system parameter setting.